اكس تول إنبلس IP508S

Full OBDII Functions

• Read Trouble Codes: Show the detailed description of the Diagnostic Trouble Code (DTCs)
• Clear Trouble Codes: Turns off Check Engine Light (MIL), clears codes and resets monitors
• Live Data: Show the information of continuous data stream from a vehicle in live graphic (waveform) display.
• Read Freeze Frame: Check the certain vehicle conditions which are recorded by the on-board computer at the time the emission-related fault occurs.
• Read ECU Information: Display the information such as VIN (Vehicle Identification Number), CID (Calibration ID) and CVN (Calibration verification number), etc.
• Component Test: Certain vehicle components can be actuated by commands sent from the scanner to test their operability
• On-Board Monitor Test: Retrieves and displays test results for emission-related powertrain components and systems.
• O2 Sensor Monitoring Test: Allows retrieval and viewing of O2 sensor monitor test results for the most recently performed tests from the vehicle’s on-board computer.
• I/M Readiness: Shows whether the various emissions-related systems on the vehicle
• EVAP System Test: Allow you to initiate a leak test for the vehicle’s EVAP system.

15 Hot Mantenance Services

• Power Balance:Testing of cylinder tightness and balance and adjustment of cylinder power balance.
• Seat Calibration:After the seat control module is repaired, the internal data of the seat module is automatically configured to ensure that the seat adjustment function works properly.
• Gear Learning：When the vehicle engine is overhauled, the crankshaft position sensor is replaced or the timing belt is replaced after the crankshaft position sensor needs to be learned with a diagnostic device to ensure that the engine is running properly.
• Gearbox Match：When replacing the transmission assembly, transmission control module, transmission solenoid valve, it is necessary to use the tester transmission matching function to write the serial number of the newly replaced parts, matching and self-learning.
• Suspension：Air suspension repair to match the suspension system and also adjust the vehicle's body height.
• Oil Rest: Reset the Engine Oil Life System, which calculates the optimum oil life change interval based on the vehicle's driving conditions and climate. The oil life reminder must be reset each time the oil is changed so that the system can calculate when the next oil change is required.
• TPMS Reset: Tire Pressure Monitor System (TPMS) Reset allows you to quickly look up the tire sensor IDs from the vehicle ECU, as well as to perform TPMS replacement and reset procedures after tire sensors are replaced.
• SAS: SAS reset supports recalibration of the steering angle sensor. After the calibration is successfully completed, the SAS fault memory will be automatically cleared.
• EPB: Reset the electronic parking brake system and brake pads, which also supports the brake pad replacement (retraction, release of the brake pump), G-sensor and body angle calibration.
• BMS Reset: The Battery Management System (BMS) allows the scan tool to evaluate the battery charge state, monitor the close-circuit current, register the battery replacement, and activate the rest state of the vehicle.
• Injector Coding: Write the identification code of the injector into the ECU so that the ECU can recognize and work normally.
• DPF: DPF regeneration is used to clear PM (Particulate Matter) from the DPF filter through continuous combustion oxidation mode (such as high temperature heating combustion, fuel additive or catalyst reduce PM ignition combustion) to stabilize the filter performance.
• ABS Bleeding: After the gear learning is successful, the MIL will be closed. This function can complete the self-learning of the gearbox and improve the quality of shifting.
• Throttle Relearn: Initialize the throttle actuators to the default state for regulating throttle (or idle engine) operations accurately.

8 in 1 Live Data Graph

• The XTOOL IP508S shows you live sensors data and provides data graphing for intuitive diagnostics and monitoring your vehicle performance, help customers to better analyze the abnormal parameter.
• When using the function of reading data stream, Inplus IP508S supports selecting 8 pieces of data at the same time to form a data flow chart, which is convenient for you to understand the status of each module more intuitively.

Share Report via Wi-Fi

Rather than taking the additional hassle, with this XTOOL scanner, you would easily be able to share the diagnostics report to your clients or technicians via Wi-Fi. They would take a look at the full, clear, and accurate diagnostic report, and then understand what would need to be done. No more Googling unreliable fixes that would waste your energy.